3Cr-3Mo二次硬化钢的回火组织和力学性能

研究了3cr—3Mo二次硬化钢淬火回火后的组织和力学性能。结果表明：随回火温度的升高，试验钢中先后析出M3c、M2c和M7C3等碳化物，在575℃回火时硬度达到峰值；400一575℃回火后试验钢的抗拉强度约为l600MPa，冲击韧性为30J／cm^2；回火温度高于600℃时，强度和硬度迅速下降，冲击韧性增加；640℃回火时，以M2C型碳化物为主，抗拉强度为1100MPa，冲击韧性增加至55J／cm^2。     

超临界萃取装置高压快开密封结构改进设计

对普遍采用的以橡胶O形环作为自紧密封件的高压快开密封装置密封部位的结构进行了改进,彻底解决了橡胶O形环在卸压后发生膨胀,将筒体端部法兰与密封盖卡死的问题。开发出了1种新的组合密封环,该密封环可广泛用于超临界萃取装置上。     

4%Cr铸钢支承辊热处理工艺

以太钢1549轧机采用的4%Cr铸钢支承辊为依托,研究了该辊子从铸造成形到最终精加工之间的三次热处理工艺。最终达到其技术要求:辊身硬度65~70HS、淬硬层深≥70 mm、辊颈硬度42~48HS。     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

运用现代CFD方法设计高效率的汽轮机(续前期)

论述了运用现代计算流体动力学(ComputationalFluidDynamics,CFD)技术设计高效率汽轮机的方法,典型应用的实例有全三维叶片级流场、叶片汽封和排汽蜗壳计算。计算结果和实际是相符的。进一步对结构性单元和非结构单元程序的计算结果进行了比较,已证明,非结构单元CFD程序用于复杂形状的流场计算时,结果与实际相当一致,并具有独特的功能。     

Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响

主要研究了Cr对低碳Si-Mn系TRIP钢组织与力学性能的影响。首先利用Formastor-F型膨胀仪测定了含Cr和不含Cr两种低碳钢的连续冷却转变(CCT)曲线,分析指出了Cr对连续退火工艺的潜在影响;然后采用Gleeble-3800热/力模拟试验机对两种钢的薄板试样进行了连续退火模拟实验,并通过拉伸试验测定了力学性能;最后采用金相、扫描电镜、X-射线衍射分析等技术考察分析了两种钢的显微组织。结果表明:含Cr的TRIP钢的组织比较细小,铁素体晶粒近似等轴分布;两种TRIP钢的残余奥氏体含量相近,但含Cr钢的残余奥氏体中的含碳量较高。分析认为这是由于含Cr钢在热轧阶段较易生成细小的组织,而在热处理阶段则抑制贝氏体的生成,最终获得稳定的残余奥氏体。     

18臂机械井径与磁法井径组合测井仪原理及应用

文章主要介绍了18臂机械井径与磁法井径组合测井仪的仪器结构、主要技术特性、测量原理及测井资料在油田中的应用。通过对测井资料的分析，阐述了该仪器在套损检测、补贴效果检查、射孔工程作业效果评价等方面的应用，为油田套管分析提供了可靠的保证。     

Preparation and Properties of Rare Earth Modified Carbon Black/Natural Rubber Composites

The oxides Eu, Ho, Er and Dy were used to prepare the hydroxides of rare earth modified carbon black. Then natural rubber latex （NRL） was added into the reactor. The system reacted at 85 ℃ with stirring for 1 h to prepare powdered HAF-Ln（OH）3/NR composites. The effects of the kind and content of Ln on the particle size distribution of P [ NR/HAF-Ln （OH）3 ] and mechanical properties of its vulcanizate were studied respectively. It is found that rare earth can help to get the powder of the composite, the product particle with a diameter less than 0.9mm will be get when the composites containing the compound of Ho, Er and Dy with dosage of 1.0, 1.0, O. 5 percent, respectively. The adding of Ln can improve the tensile strength and tear strength of the vulcanizate effectively, what＇s more, Er and Dy can decrease the permanent set of vulcanizate significantly. The SEM studies shows that P[ NR/HAF-Dy （OH）3 ] vulcanizate shows superior mechanical properties that depend primarily on the absence of free carbon black, the fine dispersion of carbon black in the rubber matrix and better polymer-filler interaction.     

Performance of natural‐fiber–plastic composites under stress for outdoor applications: Effect of moisture,temperature, and ultraviolet light exposure

The effects of moisture, temperature, and ultraviolet (UV) light on performance of natural‐fiber–plastic composites (NFPC) were assessed. We conducted short‐term tests in the laboratory and long‐term tests under natural exposure and measured changes in mechanical properties and color in samples of the composite. Chemical changes of the composite's materials were measured by X‐ray photoelectron spectroscopy to elucidate the mechanisms of chemical transformations on the material surface. Relative humidity highly affected the modulus of rupture (MOR) and the modulus of elasticity (MOE), and had a greater effect than temperature and UV exposure on performance of the composite. The lightness of the composite was increased by the UV effect in the short‐ and the long‐term tests. The X‐ray photoelectron spectroscopy (XPS) analysis suggested that the composite was protected by the UV absorber. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 2570–2577, 2006     

关于从旋涡炉渣回收铜的研究

介绍了用自然澄清法降低、回收旋涡炉渣中的铜的方法。该方法工艺简单。操作方便，不仅降低冶炼成本，同时提高了经济效益。